Jump to content

snake444

Members
  • Content Count

    1
  • Joined

  • Last visited

Community Reputation

0 Neutral

About snake444

  • Rank
    Noob
  1. when i run the script i get error, log : eth1: No such device IPv6 configuration failed! the script's code: #!/bin/sh if ! [ -f /proc/net/if_inet6 ] then echo "IPv6 is not installed!" 1>&2; exit 1; fi ifconfig sit0 up \ && ifconfig sit0 inet6 tunnel ::213.121.24.85 \ && ifconfig sit1 inet6 add 2001:618:400::591:cb1f/128 \ && route -A inet6 add ::/0 gw fe80::d579:1855 dev sit1 \ && route -A inet6 add 2000::/3 gw fe80::d579:1855 dev sit1 \ && ifconfig eth1 up \ && ifconfig eth1 inet6 add 2001:618:400:b733::/64 \ && echo 1 > /proc/sys/net/ipv6/conf/all/forwarding \ && echo 'interface eth1 { AdvSendAdvert on; prefix 2001 :618:400:b733::/64 { AdvOnLink on; AdvAutonomous on; }; };' > /etc/radvd.conf \ && /etc/init.d/radvd start \ && echo "IPv6 configuration completed" || \ { echo "IPv6 configuration failed!" 1>&2; exit 1; } and when i do ifconfig there is: snake@delta:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:E0:4C:77:CD:1D inet6 addr: fe80::2e0:4cff:fe77:cd1d/64 Диапазон:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:270656 errors:0 dropped:0 overruns:0 frame:0 TX packets:250379 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:275446383 (262.6 MiB) TX bytes:21518725 (20.5 MiB) Interrupt:20 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Диапазон:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:84 errors:0 dropped:0 overruns:0 frame:0 TX packets:84 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:4817 (4.7 KiB) TX bytes:4817 (4.7 KiB) ppp0 Link encap:Point-to-Point Protocol inet addr:89.1.203.31 P-t-P:212.29.206.60 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1 RX packets:269808 errors:0 dropped:0 overruns:0 frame:0 TX packets:249776 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:269452852 (256.9 MiB) TX bytes:15987305 (15.2 MiB) sit0 Link encap:IPv6-in-IPv4 inet6 addr: ::89.1.203.31/96 Диапазон:Compat inet6 addr: ::127.0.0.1/96 Диапазон:Unknown UP RUNNING NOARP MTU:1480 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) sit1 Link encap:IPv6-in-IPv4 inet6 addr: 2001:618:400::591:cb1f/128 Диапазон:Общий inet6 addr: fe80::5901:cb1f/64 Диапазон:Link UP POINTOPOINT RUNNING NOARP MTU:1472 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:7 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:588 (588.0 b) any ideas how to solve that problem? i tryed editing the script and changing all eth1 to eth0 because in ifconfig i dont see any eth1 connection but i got error too snake@delta:~$ sudo sh LinuxScript.sh SIOCSIFADDR: File exists IPv6 configuration failed! thanks.
×
×
  • Create New...