Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Linux Slide Show
#1

Ok, those of you who read my Linux is Slow thread know that I had a lot of fun getting linux to run at a decent speed. But IT WORKS!! Well minus reader rabbit in wine. But not a big deal. I'll probably try again some time.

 

New project, and this is going to be harder. I'll do it in DOS if I have to, but I'ld rather do it in linux. The nice thing is I CAN do it in Dos. So if all else fails, that's where I'll be going. Anyway here goes...

 

I've got a 486 laptop with 16 meg of ram. All I want to do with it is run a slideshow. That's it. Boot up and slideshoow starts. Nothing else. To get the pictures on the system I will be taking the hard drive out, putting it into another machine, mounting the drive and moving them over. So I don't need networking, I don't need a keyboard, mouse, anything but the slideshow.

 

Here's what I'm thinking. I need a very stripped down version of slackware(or maybe RedHat 7.x?), svgalib instead of X and ZGV.

 

Nothing is ever that simple. So here go my questions...

 

1. How do I get rid of all the stuff I don't need to make my linux distro lean lean lean, like as in lean enough to run on a 486 with 16 meg of ram.

 

2. How do I boot directly into the slideshow bypassing the login altogether?

 

3. What other problems am I going to run into.

 

Thanks in advance...

Zane

Reply
#2

Hi,

 

You will want to try: ZipSlack [/url][url=http://www.slackware.com/zipslack/]http://www.slackware.com/zipslack/ it is designed

to run on machines with only 8MB of ram. Then just install open office on it.

Reply
#3

Quote:Hi, 

You will want to try: ZipSlack [/url]http://www.slackware.com/zipslack/ it is designed

to run on machines with only 8MB of ram. Then just install open office on it.



[url=<___base_url___>/topic/1798-linux-slide-show/?do=findComment&comment=6339]<{POST_SNAPBACK}>
 

I'm sorry I'm a little lost. Why would I want to install Open Office? It's HUGE and processor intensive. I'm sure it would KILL a 486 computer. However, thanks for the info on the distro, I'm looking into it. If it will run on a 486 with only 8 meg of ram it could be perfect assuming I can gut all the stuff out that I don't need. Hard drive is only going to be a 2 gig drive.

Reply
#4

Quote:Hi, 

You will want to try: ZipSlack [/url]http://www.slackware.com/zipslack/ it is designed

to run on machines with only 8MB of ram. Then just install open office on it.



[url=<___base_url___>/topic/1798-linux-slide-show/?do=findComment&comment=6339]<{POST_SNAPBACK}>
 

Ok after an initial look I'm thinking this will be perfect. Only needs 100 meg of hard drive space!!!! Yeah! Maybe I won't have to strip anything off. SweeT.

 

Thanks for the TIP. OOOH and I can install from a Zip Drive. PERFECT since I don't have a CD ROM on that laptop but I do have a Zip Drive. I'm getting giddy with anticipation here. I'm still going to use my original plan of svgalib instead of X and ZGV. I'll let you know how it goes.

Reply
#5
i have used zipslack at one point or another to 'revive' antique hardware. it defn one of the better distros for running on low spec machines.
Reply
#6

Hi,

 

I think you can use a ZIP disk: [/url][url=http://www.slackware.com/zipslack/install.php]http://www.slackware.com/zipslack/install.php that tells you

how to install it. When in DOS just access the zip disk instead of Floppy disk drive :)

Reply
#7
No progress here yet. I've been too busy. But still plan to do this.
Reply
#8

Any progress??? I just tore apart an old laptop and started to build a wood box to build a picture frame...

 

Worst case, can someone reccomend linux slideshow software that I can start from a command line??

Reply
#9

I downloaded slackware and installed it. Anything that looked like I wouldn't need I didn't install when install the packages. However, on the developement stuff, I thought I might need to compile some stuff so I probably installed WAY more than I needed there. I wanted to make sure that I would be ale to compile anything I needed.

 

I did NOT install X. I did install SVGALIB. And seejpeg. seejpeg even has a slideshow option, a randomize, option etc... seemed perfect...

 

So... I run seejpeg and it works... sorta... I flip to a graphic screen with really weird stuff above and below... and about half an inch that shows a portion of the image. It is bizzar. If I choose a different mode... like G800x600x256 then I get text above and weird stuff below. No errors though.

 

Is this a problem with my SVGALIB installation or a problem with seejpeg???

 

 

Any help sorting this out would be appreciated.

Reply
#10

Well looks like I fixed it....sortof

 

I uncommented this line in /etc/vga/libsvga.config

 

chipset vesa

 

I run seejpeg with the following parameters...

 

seejpeg -c -F G800x600x16M -s 30 -r *

 

That works pretty well for a randomized slideshow with 30 seconds between showings...

 

Problem is that all my pictures are 1600x1200 so only 1/4 the image shows at a time. So I need to resize. You are suppose to be able to scroll to see the whole image. I can't I don't know why this is. I can scroll horizontally but not vertically. I can scroll through the image twice horizontally. Weird

 

Anyway, I'll keep you posted on the progress. I may reinstall slackware yet again to see if I can get rid of some packages I don't need. Unless someone can tell me how to remove packages without reinstalling.

Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)